Monday, March 19, 2018

Vintage Craftsman 2.3 16 Chainsaw

So I've been on the lookout for older chainsaws that are 70's and 80's.  The old all metal ones that they "don't make like they the use to" kind of thing.  Now I'm in an area that was never logging so they have not been plentiful.  Either too beat up or someone thinks there worth a lot of money, regardless of condition.  So anyways I finally got a decent one that is the basic hasn't ran in years and just getting rid of it.  It's a Craftsman 2.3.  My research shows it was probably made by Poulan in the early 70s.  It's a 38cc saw with a 14" bar and chain, though the plate says 16, so it's original bar was probably a 16".  But this actually fills a niche for me as I don't have a smaller saw and it is one of those one handers for limbing jobs, etc.  So kind of neat to me. 

So here it is as it came.  Pretty good condition really, just dirty.





drained the awful gas and sprayed out the tank some with carb cleaner.  Did this s few times.  To give an idea how bad it is the filter is stuck to the bottom of the tank.



back to the bench and will start cleaning it out



cleaning up really nice.  I just used some gas and toothbrush and a wipe cloth







carburetor is done.  The diaphragm and fuel pump are toast so I ordered a set to replace it. 








First is running a new fuel line.  Here you can get a sense for the hard curve it has.



The old fuel filter finally released from the tank bottom after having some gas in it for a few days...



Just for my own amusement I wanted to see if I could get this new line routed without having to take the flywheel off.  So I got some 50lb. braided fishing line and a hook and double it up and ran through the old line and pulled it up through that tight curve.

















So I tied off the knot and started trying to coax it through.  I wish I could tell you it worked but the turn was too hard and it wasn't a continuous tube.  One ended and then it had to go into another opening while making that 90 degree turn and up.  It didn't happen and I decided just to see if I could pull it through with force and the knot pulled through the tube.  A better know maybe would have been better.  I do think this idea would work if you have a simpler routing path. 

So had to take the flywheel off.  I used an impact driver for this.





while blowing out the area first I got really lucky as a I forgot to grab the flywheel key before I started blowing.  After I got done I realized it was gone and looked down and it was right by my foot.  That was fortunate cause it's little and could have gone anywhere never to be found..





So routing the line was easy at this point.  Hemostat pliers really make grabbing and pulling on the fuel lines easy. 





Now for the carburetor.  I cleaned it out and then replaced the diaphragm, fuel pump, and gaskets.  All these were old and cracking.







Alright got her all put back together.  Got it fired up and tuned the carb and it's running pretty good.  I took it out by the wood pile to run it through a log.





Not a bad deal for a total cost of about $22

Thanks for looking folks!

4 comments:

  1. I'm having to do the same with mine and your pics and information will help a lot. Thank you for posting this!

    ReplyDelete
  2. I recently unearth one of these as well. The fuel mixture advice on the sticker says half a pint to 1 gallon of gasoline which seems like a pretty steep oil to gas ratio. I ran a 40 to 1 and it and it ran and shut off a few times. Have you been able to find a link for a manual?

    ReplyDelete
  3. I as well just purchased the same saw and own 2 other craftsman 2.0, the ratio i was told by all 3 previous owners was a crazy amount and its worked well so far but with very little use i cant garuntee it to be spot. 16.1 .... I know thats 8oz per gallon.. But when a man tells me his dad was 1st owner him 2nd and was told to use the ratio i tend to believe the old fart..

    ReplyDelete
  4. MANY thanks for the info. I have owned and old Craftsman 2.3A chainsaw for the past 50 years but have not run it for about 35 years. So I was trying to get it started. I couldn't figure out how to replace the fuel line. I wish you had mentioned the size of the line---there are sooo many different sizes. But I sincerely appreciate the wonderful photos and info.

    ReplyDelete